<em id="i7peh"><acronym id="i7peh"></acronym></em>
  • <dd id="i7peh"><track id="i7peh"></track></dd>
    1. <rp id="i7peh"></rp>

      <dd id="i7peh"><center id="i7peh"></center></dd>

      采購信息

      采購商用車CUBING檢具系統 參數 圖 查看采購商

      長期采購 | 2020-08-26 11:14:34

      采購信息內容

      采購商用車CUBING檢具系統,我們需要承接方:設計、制作、安調,國內使用,商用車 總裝車間 北京,我這是東風設計院的。        湖北 十堰

      CUBING檢具系統:Checking Fixture Cubing System:
      1.部件信息 Component Information
      1)產品相關參數 Product related parameters
      圖1



      產品的外形尺寸-約2450x440x1200毫米。Overall dimension of product –
      Approximate 2450x440x1200 mm.
      2)分解圖 Explosive view.
      圖2 3



      2.工作過程:work process:
      圖4



      前端模塊檢查夾具主要用于實際檢查和匹配。
      The front-end module inspection fixture is mainly used for actual inspection and
      matching.
      進行部分產品設計和工藝驗證。
      Carry out partial product design and process verification.
      識別產品設計和過程中的零件對零件的配合問題和質量問題。
      Identify the part-to-part fit and quality problems in product design and process.
      提供一種持續的方法,用于對最新的前端模塊組件進行預驗證。
      Provide a continuous method for pre-verification of the latest front-end module
      components.
      根據需要,對主量規上的零件更改或更正進行評估,以驗證零件的配合。
      As needed, evaluate the part changes or corrections on the master gauge to verify
      the fit of the parts.
      用于診斷產品設計、質量問題、過程問題和優化零件匹配的工具。
      Tools for diagnosing product design, quality issues, process issues and
      optimizing part matching.
      旨在評估前端模塊組件是否匹配和完成。
      Aim to evaluate whether the front-end module components are matched and
      completed.
      確定問題的根本原因,在匹配的情況下,哪些部分將被修改。
      Determine the root cause of the problem and in the case of a match, which parts
      will be modified.
      建立統一的流程和標準,驗證新車型的功能外觀。
      Establish unified procedures and standards to verify the functional appearance of
      new models.
      名義公稱值或單元檢查夾具將用于評估零件。
      The nominal value or unit check fixture will be used to evaluate the part.
      3) 技術說明 Technical Description
      基準和特性要與安裝意圖一致。
      Benchmarks and characteristics should be consistent with the installation intent.
      測量點遵循 CCP 和工藝要求。The measurement points follow CCP and
      process requirements.
      用于評價零件和其與周圍零件的匹配關系,的零件能在類似總裝條件下無
      故障地安裝和拆卸。與零件匹配的相關匹配區域要局部或全部做出,連接處寬
      度大于 100mm。
      Used to evaluate parts and their matching relationship with surrounding parts, the
      parts can be installed and disassembled without failure under similar general assembly
      conditions. The relevant matching area matching the part should be made partially or
      completely, and the width of the joint should be greater than 100 mm.
      保證零件的正常安裝,及相鄰零件的位置關系,待測零件安裝及拆裝后,
      不能損壞或者劃傷主檢具。
      Ensure the normal installation of parts and the positional relationship of adjacent
      parts. After the parts to be tested are installed and disassembled, the main inspection
      tool cannot be damaged or scratched.
      零件安裝方便,零件在檢具上能夠體現其安裝在整車上的功能,滿足其技
      術要求, 能夠和生產零件替換使用,保證可拆卸,以便于獨立的評價分析某些
      特定零件。
      The parts are easy to install. The parts can reflect its function of installing on the
      whole vehicle on the inspection tool, meet their technical requirements, can be
      replaced with production parts, and ensure that they can be disassembled to facilitate
      independent evaluation and analysis of certain specific parts.
      要求主檢具型面部分耐磨、不變形。
      The surface of the main inspection tool is required to be wear-resistant and not
      deformed.
      功能主檢具要滿足測量要求,即保證每個檢具模塊功能區域用測量機能夠
      進行檢測。
      The functional main inspection tool must meet the measurement requirements,
      that is, to ensure that the functional area of each inspection tool module can be
      detected by the measuring machine.
      零件本身功能主檢具盡可能保證加工基準和測量基準一致。
      The main inspection tool for the function of the part itself ensures that the
      processing benchmark and the measurement benchmark are consistent as much as
      possible.
      主檢具要求定位準確、活動自如、操作安全方便;其檢測項目應包括必要
      的定位孔、定位面、功能面、裝配孔、表面件配合型面及輪廓等。
      The main inspection tool requires accurate positioning, free movement, safe and
      convenient operation; its inspection items should include necessary positioning holes,
      positioning surfaces, functional surfaces, assembly holes, surface parts matching
      profiles and contours, etc.
      檢具在設計過程中需有測量基準(孔、軸、球、面),基準坐標系方向與汽
      車整車坐標系方向相重合,測量基準與檢具骨架整 體加工后在基準上標識
      X、Y、Z 軸整車坐標系的實測值。為三坐標對檢具精度進行驗證時提供測量基
      準依據。
      In the design process of the inspection tool, a measurement datum (hole, axis,
      sphere and surface) is required. The direction of the datum coordinate system
      coincides with the direction of the vehicle coordinate system. The measurement
      datum and the inspection tool frame are processed as a whole and marked on the
      datum. The actual measured value of the X, Y and Z axis vehicle coordinate system. It
      provides the basis of measurement when verifying the accuracy of the gage with three
      coordinates.
      銷定位的設計采用獨立原則。推薦采用彈簧座錐形銷結構。
      The design of pin positioning adopts the principle of independence. It is
      recommended to adopt a spring seat conical pin structure.
      定位面的法向須施加外力以確保產品正確定位,夾緊力不大于 5KG,不允
      許有強制夾緊現象。
      The normal direction of the positioning surface must be applied with external
      force to ensure the correct positioning of the product. The clamping force is not more
      than 5KG, and forced clamping is not allowed.
      快速夾緊器的壓頭推薦采用帶彈簧的橡膠壓頭。
      The indenter of the quick clamp is recommended to use a rubber indenter with a
      spring.
      在有定位銷或檢驗銷的地方,壓頭要設計成中空的形式。
      Where there are positioning pins or inspection pins, the indenter should be
      designed in a hollow form.
      在有孔或其他特征要素需要測量的地方,壓頭要設計成可保證測量的形
      式。
      Where there are holes or other characteristic elements that need to be measured,
      the indenter should be designed to ensure the measurement.
      基準面平面度:0.05/1000×1000。
      Flatness of reference plane: 0.05/1000×1000.
      二基準面之間垂直度:0.10/1000。
      The perpendicularity between the two reference planes: 0.10/1000.
      RPS 定位點相對與測量基準位置度:± 0.1。
      The relative position of the RPS positioning point to the measurement reference
      position: ± 0.1.
      RPS 定位點與輔助 RPS 定位點位置度:± 0.1。
      RPS positioning point and auxiliary RPS positioning point position degree: ±
      0.1.
      測量輪廓面相對與測量基準(RPS)輪廓度:± 0.10。
      The profile of the measurement profile surface relative to the measurement
      reference (RPS): ± 0.10.
      非重要輪廓面相對與測量基準(RPS)輪廓度:± 0.2。
      The profile of the non-important profile surface relative to the measurement
      reference (RPS): ± 0.2.
      輪廓檢驗模板相對與測量基準(RPS)輪廓度:± 0.15。
      The profile of contour inspection template relative to the measurement reference
      (RPS): ± 0.15.
      定位孔(銷)相對與測量基準(RPS)位置度:Φ0.05。
      The relative position of the positioning hole (pin) to the measurement reference
      (RPS): Φ0.05.
      測量孔(銷)相對與測量基準(RPS)位置度:Φ0.05。
      The position of the measuring hole (pin) relative to the measuring standard
      (RPS): Φ0.05.
      劃線孔位置度:Φ0.4。
      The position of the marking hole: Φ0.4.
      刻線精度:±0.2。
      Scribing accuracy: ±0.2.
      定位銷(測量銷)在其對應的襯套內擺動(指根部)不大于 0.02。
      The locating pin (measurement pin) swings (referred to at the root) in its
      corresponding bushing not more than 0.02.
      滑軌間隙擺動不大于 0.02。
      The slide rail clearance swing is not more than 0.02.
      深度規臺階面齊平度 0.05。
      The flushness of the depth gauge step surface is 0.05.
      輪廓檢驗模板在檢具上擺動不大于 0.05。
      The swing of the contour inspection template on the inspection tool shall not
      exceed 0.05.
      定位襯套孔(測量襯套孔)直徑精度等級 H7。
      Positioning bushing hole (measurement bushing hole) diameter accuracy class
      H7.
      定位銷(測量銷)與定位襯套孔(測量襯套孔)接觸直徑段精度等級 h6。
      The positioning pin (measurement pin) and the positioning bushing hole
      (measurement bushing hole) contact the diameter of the accuracy class h6.
      定位銷(測量銷)與零件接觸直徑段精度等級 f8。
      Locating pin (measuring pin) and parts contacting diameter section accuracy
      class f8.
      檢具底板、結構件和樣板建議采用鋁鎂合金 ( ZL104 LY12
      ALMg4.5Mn0.7)。
      It is recommended to use aluminum-magnesium alloy (ZL104 LY12
      ALMg4.5Mn0.7) for the bottom plate, structural parts and sample plates of the
      inspection tool.
      模擬塊建議采用鋁鎂合金 (ALMg4.5Mn0.7)或可加工塑料(CIBA BM5166)。
      It is recommended to use aluminum-magnesium alloy (ALMg4.5Mn0.7) or
      machinable plastic (CIBA BM5166) for the simulation block.
      定位測量用的銷和孔套建議采用合金鋼材料(GGr15,40Cr)。
      It is recommended to use alloy steel materials (GGr15, 40Cr) for pins and hole
      sleeves for positioning measurement.
      測量基準建議采用不銹鋼材料(1Cr13S 1Cr13Ni9Ti SUS303 SUS304)。
      It is recommended to use stainless steel material (1Cr13S 1Cr13Ni9Ti SUS303
      SUS304) for the measurement standard.
      某些特定零件(安裝保險桿)有導板連接,要求導板等零件能夠和導板檢
      具進行交換。
      Some specific parts (installation of bumpers) are connected with a guide plate,
      which requires that the guide plate and other parts can be exchanged with the guide
      plate inspection tool.
      檢具的大底板其上表面作為安裝和測量的基礎平面應無明顯的走刀痕跡。
      日常使用中可承受檢具的重量,不變形。
      The upper surface of the large base plate of the inspection tool is used as the
      basic plane for installation and measurement, and there should be no obvious traces of
      the tooth mark. In daily use, it can bear the weight of the inspection tool without
      deformation.
      上平面應刻 100 mm 間隔的坐標線。線深 0.5mm 寬 0.5mm。
      The upper plane should be engraved with coordinate lines at 100 mm intervals.
      The line is 0.5 mm deep and 0.5 mm wide.
      檢具上 RPS 點應有標識。
      The RPS point on the inspection tool should be marked.
      檢具上的測量孔與測量銷有對應標識。
      The measuring hole on the gage has a corresponding mark with the measuring
      pin.
      測量銷標識被測直徑;通止規標識臺階差值。
      The measuring pin identifies the measured diameter; the through stop gauge
      identifies the step difference.
      附檢具使用說明書。 Instruction manual for checking tool is attached.
      檢具銘牌:檢具號 、零件號、車型、圖紙日期、重量、制造單位、主機
      廠、造日期。
      Check tool nameplate: Check tool number, part number, model, drawing date,
      weight, manufacturing unit, OEM, manufacturing date.
      注:- 業主將與零部件供應商建立會議,以建立和同意產品基準。它必須匹
      配的過程,將用于定位到車輛的組件。
      Note :- owner will establish meetings with component suppliers to
      establish and agree on the product datum’s. It must match the process that
      will be used to locate the components to the vehicle.
      裝配夾具,匹配測量報告
      Assembly Fixture - Cubing Measurement Report
      圖5~9



      備注. Remark :
      流程為暫定工藝流程(僅供參考,可根據需要變化)
      Tentative Process Flow for FEM assembly (Only for reference purpose,
      may vary as per requirement)
      3.保險杠間隙面差草案 ARR_ BUMPER_NEWGAPNFLUSH_Draft.
      圖10~19










      檢具相關采購信息
      采購商用車CUBING檢具系統 參數 圖[2020-08-26 11:14:34]

      采購商用車CUBING檢具系統,我們需要承接方:設計、制作、安調,國內使用,商用車 總裝車間 北京,我這是東風設計院的。

      采購三門峽中測量儀YS00078457小連桿綜合測量檢具 圖[2020-07-31 14:21:39]

      采購三門峽中測量儀YS00078457小連桿綜合測量檢具,一臺多少錢?報個經銷商的最優惠價,謝謝。  &nbs

      采購上海華莊模具汽車制動管的彎曲工裝和檢具[2020-01-06 15:16:21]

      采購上海華莊模具汽車制動管的彎曲工裝和檢具,咱們家跟汽車管路供應商有合作的有哪幾個品牌?聯系我們。  &nbs

      采購后三角窗開口檢具 圖[2019-11-16 10:25:11]

      采購后三角窗開口檢具,一左一右,先要2個,自己用。   四川 成都   

      汽車內飾零件產品及摸具 檢具加工定制[2019-09-02 14:21:12]

      汽車內飾零件產品及摸具 檢具加工定制,尋杯體總成廠家,能做我們提供3D,D093項目本體總成產品向貴司進行詢價,附件為詢

      采購上海紫燕模具工業公司檢具[2019-08-13 15:14:22]

      采購上海紫燕模具工業公司檢具,克萊斯勒,需檢具報價。    江蘇_南京

      求購檢具設計開發快速設計的插件 圖[2018-12-20 10:12:10]

      求購檢具設計開發快速設計的插件,檢具設計時開發的一種幫助快速設計的插件,我們要這種設計軟件,有的請答復,我們之前還給上海

      采購無錫富瑞德缸體冷卻槽深度檢具[2018-04-02 14:23:54]

      采購無錫富瑞德缸體冷卻槽深度檢具,型號規格:F3171040009,麻煩您確認下價格,謝謝。   廣東 廣州

      采購外購件檢具 圖[2018-03-19 14:47:28]

      采購外購件檢具,我需要制作檢具,要求在Volvo Supplier Panel里,此零件為外觀件,表面需蝕紋,檢具需按V

      采購無錫富瑞德綜合檢具深度表及基座[2017-10-14 18:54:55]

      采購無錫富瑞德綜合檢具深度表及基座,規格型號:F6151040014,576面高度深度表;1個,現在是報價階段。&nbs

      出口采購大連盤起檢具 圖紙[2017-09-28 11:24:45]

      出口采購大連盤起檢具,我有些檢具要加工生產,我先發幾張圖紙給你看看能不能做,能做的話就報價給我,訂貨都是按個訂貨的,不是

      定制加工檢具[2017-02-05 10:18:26]

      定制加工檢具,下面這些數據通用項目,做總成檢具即可,可以的話我發3D及詳細圖紙,我們是做汽車座椅配件的廠家。 

      采購無錫富瑞德綜合檢具深度表及基座[2016-09-05 13:15:52]

      采購無錫富瑞德綜合檢具深度表及基座,規格型號:F6151040014,576面高度深度表,要一個。 廣東 廣州 

      采購無錫富瑞德綜合檢具深度表及基座[2016-09-02 14:39:20]

      采購無錫富瑞德綜合檢具深度表及基座,規格型號:F6151040014,576面高度深度表,要1個。  

      訂做檢具[2015-04-28 11:09:54]

      訂做檢具,汽車高位剎車燈的,需要報價,謝謝! 廣東深圳

      天下汽配小程序
      日韩在线 无码 精品,最新高清无码专区在线视频,人妻 制服 出轨 中字在线,日本无码中文一区免费